HP인증HP0-207시험을 패스하여 자격증을 취득한다면 여러분의 미래에 많은 도움이 될 것입니다.HP인증HP0-207시험자격증은 it업계에서도 아주 인지도가 높고 또한 알아주는 시험이며 자격증 하나로도 취직은 문제없다고 볼만큼 가치가 있는 자격증이죠.HP인증HP0-207시험은 여러분이 it지식테스트시험입니다.
HP인증 HP0-207시험을 등록하였는데 시험준비를 어떻게 해애 될지 몰라 고민중이시라면 이 글을 보고ITExamDump를 찾아주세요. ITExamDump의HP인증 HP0-207덤프샘플을 체험해보시면 시험에 대한 두려움이 사라질것입니다. ITExamDump의HP인증 HP0-207덤프는HP인증 HP0-207실제시험문제를 마스터한 기초에서 제작한 최신시험에 대비한 공부자료로서 시험패스율이 100%입니다. 하루 빨리 덤프를 마련하여 시험을 준비하시면 자격증 취득이 빨라집니다.
거침없이 발전해나가는 IT업계에서 자신만의 자리를 동요하지 않고 단단히 지킬려면HP인증 HP0-207시험은 무조건 패스해야 합니다. 하지만HP인증 HP0-207시험패스는 하늘에 별따기 만큼 어렵습니다. 시험이 영어로 출제되어 공부자료 마련도 좀 힘든편입니다. 여러분들의 고민을 덜어드리기 위해ITExamDump에서는HP인증 HP0-207시험의 영어버전 실제문제를 연구하여 실제시험에 대비한 영어버전HP인증 HP0-207덤프를 출시하였습니다.전문적인 시험대비자료이기에 다른 공부자료는 필요없이ITExamDump에서 제공해드리는HP인증 HP0-207영어버전덤프만 공부하시면 자격증을 딸수 있습니다.
시험 번호/코드: HP0-207
시험 이름: HP (Procurve Adaptive EDGE Fundamentals)
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 120 문항
업데이트: 2014-03-09
아무런 노력을 하지 않고 승진이나 연봉인상을 꿈꾸고 있는 분이라면 이 글을 검색해낼수 없었을것입니다. 승진이나 연봉인상을 꿈꾸면 승진과 연봉인상을 시켜주는 회사에 능력을 과시해야 합니다. IT인증시험은 국제적으로 승인해주는 자격증을 취득하는 시험입니다. ITExamDump의HP인증 HP0-207덤프의 도움으로 HP인증 HP0-207시험을 패스하여 자격증을 취득하면 승진이나 연봉인상의 꿈이 이루어집니다. 결코 꿈은 이루어질것입니다.
HP0-207 덤프무료샘플다운로드하기: http://www.itexamdump.com/HP0-207.html
NO.1 How do ProCurve switches, configured with link aggregation (also known as port trunking),
handle broadcast traffic?
A.Broadcast traffic is flooded through all of the ports in the trunk.
B.The switch sends a query and receives permission from potential receivers before flooding.
C.Broadcast traffic is handled in exactly the same way it would be without port trunking configured.
D.Broadcast traffic is flooded through non-trunked ports, but forwarded only through one of the ports in
the trunk.
Correct:D
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.2 While using the CLI to configure a ProCurve switch, you must move from the global
configuration level to the port context configuration level for port a1. Which command do you use?
A.port a1
B.ethernet a1
C.interface a1
D.configure a1
Correct:C
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.3 You must remotely manage a customer's switch using Telnet. Which configuration/monitoring
interfaces are available? Select TWO.
A.web interface
B.menu interface
C.ProCurve Manager
D.boot monitor interface
E.command line interface
Correct:B E
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.4 You are assigned to configure ProCurve switches at a customer site for in-band management.
Which are in-band management methods? Select TWO.
A.Telnet
B.SNMP
C.XMODEM
D.serial console
E.menu interface
Correct:A B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.5 You must update the software on a customer's ProCurve Switch 5412zl. Which statement
correctly describes the process for this operation? Select TWO.
A.Use TFTP for direct serial transfer of the software.
B.Use FTP for in-band transfer of the software through an IP network.
C.Use TFTP for in-band transfer of the software through an IP network.
D.Transfer the software from your workstation using a direct serial transfer.
E.Instruct the switch to search for any available TFTP server without knowing its IP address.
Correct:C D
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.6 You have been asked to configure IGMP on a ProCurve Switch 6200yl at a customer site. What
are the steps for enabling IGMP on the switch?
A.Enter the manager level, then issue the ip igmp command.
B.Enter the global configuration context, then issue the ip igmp command.
C.Enter the VLAN context for each VLAN that will support IGMP, then issue the ip igmp command.
D.Enter the interface configuration context for each port configured with a VLAN, then issue the ip igmp
command.
Correct:C
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.7 You are installing a ProCurve switch at a customer site and must enable remote management
for network administrators. Which configuration parameter is necessary to ensure that
administrators can manage the switch even if they are on different IP networks?
A.default VLAN
B.default gateway
C.default password
D.default management profile
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.8 On switches that support the Switch Setup screen interface, which parameters can be
configured on the Switch Setup screen? Select TWO.
A.STP bridge priority
B.IP address of the TACACS+ server
C.system name and contact information
D.IP address and subnet mask for each VLAN
E.IP address and subnet mask for the default VLAN
Correct:C E
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.9 You configured Rapid Spanning Tree Protocol on four ProCurve Switch 5348xl switches at a
customer site. During the configuration, you forgot to configure the switches so that
switch-to-switch links are not defined as edge ports. Which statement describes the consequence
of your oversight?
A.The switches in the spanning tree will elect multiple Root bridges.
B.The switches will reject the spanning tree configuration and block all ports until the configuration is
corrected.
C.The switches will be unable to elect a Root bridge and will not be able to forward traffic until the
configuration is corrected.
D.The switches will require more time to elect the Root bridge and resolve the topology, but the spanning
tree will otherwise function normally.
Correct:D
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.10 You are about to update the software on a ProCurve switch. Which command do you use to view
a list of all software versions stored on the switch?
A.show run
B.show flash
C.show startup
D.show version
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.11 You are implementing a fully connected HP Switch Mesh at a customer site. Which statement
describes a valid design guideline for HP Switch Meshing?
A.A switch may be connected to no more than four mesh domains.
B.Up to five Switch 5400zl Series switches can be included in a full mesh.
C.All links in a full mesh must operate at the same speed and use the same media type.
D.When a switch is configured for HP Switch Meshing protocol, all of the ports on that switch must
participate in the mesh.
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.12 At a customer site, you have configured four ProCurve switches for HP Switch Meshing and
Multiple Spanning Tree Protocol. How will the mesh appear to non-mesh switches in the same
spanning tree domain?
A.as a single device
B.as a set of devices without redundant links
C.as devices that cannot participate in the spanning tree
D.as a set of devices with spanning tree enabled to block redundant links
Correct:A
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.13 While examining the spanning tree configuration on a ProCurve switch, you notice that one of
the ports is in the Blocking state. Which statement describes how this port will function in this
state?
A.The port is completely blocked for all purposes.
B.The switch will not forward user traffic through that port, but will forward telnet traffic.
C.The switch will not forward user traffic through that port, but will forward BPDUs through that port.
D.The switch forwards user traffic through that port, but does not receive user traffic through that port.
Correct:C
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.14 You are configuring a ProCurve Layer 2 switch to obtain time information from an SNTP server
located on a different IP network than the switch. Which configuration steps are necessary on the
switch to enable this functionality?
A.The switch cannot be configured to obtain time information from a server on a different IP network.
B.Define a default gateway for the switch, enable SNTP, use the sntp server command to enter the IP
address of the server.
C.Assign a port on the switch to a VLAN that includes the SNTP server, enable SNTP, configure the
switch for SNTP unicast mode.
D.Configure an IP address on the same IP network as the SNTP server, enable TimeP, configure the
switch for SNTP broadcast mode.
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.15 A customer is planning a Power over Ethernet deployment for a large call center that will use
VoIP telephones. While planning the wiring closets for the deployment, the customer suggests
using the uplink ports of a ProCurve Switch 2650-PWR to provide power to a ProCurve Switch
2600-8-PWR. Which statement describes a correct response to this suggestion?
A.It is only possible if the second switch is a ProCurve Switch 2626-PWR.
B.It is not possible because the 2600-8-PWR cannot act as a Powered Device.
C.It is only possible if the customer adds a ProCurve 600 EPS/RPS to the first switch.
D.It is not recommended because the second switch will not have adequate power redundancy.
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.16 How is traffic prioritization accomplished with IEEE 802.1p?
A.802.1Q-compliant devices enforce priorities based on VLAN ID.
B.802.1Q-compliant devices set one of 8 values in a 3-bit field in the VLAN tag.
C.802.1Q-compliant devices set one of 64 values in a 6-bit field in the IP datagram header.
D.802.1Q-compliant devices dedicate a portion of available bandwidth to each prioritized conversation.
Correct:B
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.17 While using the CLI to configure a ProCurve switch, you must change context from the manager
level to the global configuration level. Which command do you use?
A.exit
B.write
C.global
D.enable
E.configure
Correct:E
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.18 What are the key principles of the Adaptive EDGE architecture? Select TWO.
A.Control to the Edge
B.Control to the Desktop
C.Command from the Center
D.Management from Anywhere
E.Security throughout the Network
Correct:A C
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.19 What are the primary solution categories of the Adaptive EDGE Architecture? Select THREE.
A.mobility
B.security
C.reliability
D.availability
E.upgradeability
F.convergence
G.cost-effectiveness
Correct:A B F
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
NO.20 You are about to configure HP Switch Meshing on four ProCurve switches at a customer site.
All of the ports that will be included in the mesh are configured for membership in customer
VLANs. How will the mesh configuration affect the VLAN configuration?
A.The mesh ports will automatically become a tagged member of all configured VLANs.
B.The mesh ports will not be a member of any VLANs until you manually configure its VLAN assignments.
C.The mesh ports will not be 802.1Q-compliant and will only be able to retain membership in a single
untagged VLAN.
D.The mesh ports will automatically become a member of the default VLAN and must be configured for
other VLAN membership.
Correct:A
HP dumps HP0-207 HP0-207 pdf HP0-207자격증
ITexamdump의 HP0-S34덤프의 VCE테스트프로그램과 70-481덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 C-HANATEC131시험에 대비한 고품질 덤프와 C_FSUTIL_60시험 최신버전덤프를 제공해드립니다. 최고품질 E20-553시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기